The surface cleanliness of granite measuring tools directly affects the measurement accuracy. In daily use, it is inevitable that they will be stained with oil stains, water stains, rust stains and other stains. The cleaning methods of different stains are significantly different, and blind treatment may damage the surface of the stone. The following is a targeted cleaning plan based on the type of stains, with key points for operation:
一. Oil stains: quickly dissolve and avoid penetration. Sources of stains: lubricating oil in the measurement environment, machine oil stains, or residual grease from hand contact. Hazards: Grease easily penetrates into the micropores of granite, and long-term residue may form dark spots, interfering with the flatness judgment of the measurement reference surface.
Cleaning steps:
Emergency treatment: Immediately use a lint-free soft cloth (or absorbent paper towel) to gently absorb the surface grease after discovering oil stains, and avoid wiping to expand the scope of contamination;
Choose the right detergent: Use a neutral oil stain cleaner for stone (pH value 7-8), and do not use strong acid/alkali products (such as white vinegar, caustic soda) to prevent corrosion of the stone surface gloss;
Deep cleaning: Spray the detergent on the stain, let it stand for 1-2 minutes (stubborn oil stains can be extended to 5 minutes), wipe it clockwise with a sponge, and finally wipe it with a soft cloth dampened with clean water, and dry it naturally.
二. Water stains: timely treatment to prevent traces
Source of stains: water droplets that have not been wiped dry after measurement, condensed water in a humid environment, or residual water after cleaning.
Features: Granite has a low water absorption rate (<0.25%), and water stains are mostly surface mineral deposits, which have little effect on accuracy, but long-term accumulation will form white marks that affect the appearance.
Cleaning tips:
Daily protection: After measuring, wipe the surface moisture with a dry cloth immediately to avoid natural drying and leaving marks;
Mild water stains: Use a slightly damp soft cloth with a small amount of non-phosphorus detergent, wipe the white marks in circles, and then polish with a dry cloth;
Preventive measures: Apply a thin layer of stone protective agent (fluorine-containing formula is better) on the surface every month to form a hydrophobic film to reduce water adhesion.

三. Rust stains: Gentle rust removal to protect the stone
Source of stains: Contact with iron-containing workpieces (such as uncleaned rusted parts), metal tool residues, or iron oxide dust in the environment.
Hazards: The iron ions in the rust may react with the minerals in the stone to form deep rust stains that are difficult to remove.
Treatment method:
Preliminary cleaning: Use a soft brush to gently sweep away the floating rust on the surface, and avoid scratching and causing rust to embed into the stone;
Special rust remover: Use a weak acid rust remover paste for stone (containing oxalic acid, concentration ≤5%), and avoid metal parts (such as fixing screws on measuring tools);
Operation points: Apply the rust remover paste evenly to the rust spots (thickness of about 2mm), cover with plastic wrap to prevent air drying, and wipe it with a wet sponge after standing for 10 minutes. Repeat 2-3 times to remove stubborn rust spots, and finally rinse the residual agent thoroughly with clean water.
四. Pigment stains: Targeted dissolution, use grinding with caution
Source of stains: Paint dripping in the measuring area, oil pen/ink used for marking, or pigment splashed during processing.
Difficulty: The colorant in the pigment may react chemically with the surface of the stone, especially dark pigments (such as red paint, ink), which are easy to solidify into a film after drying.
Cleaning plan:
Fresh stains: When the paint/ink is not dry, use a cotton swab dipped in a small amount of alcohol (or stone-specific stain remover) to apply it. After it gradually dissolves, use a dry cloth to absorb it to avoid spreading;
Solidified stains: Use a fine-grained (800 mesh or more) stone decontamination abrasive paste and a wool felt pad to gently rub in circles (the force should be appropriate to avoid scratches), and finally wipe it clean and polish it with clean water;
Taboo: Strong solvents such as banana water and thinner are prohibited, which may dissolve the protective layer on the surface of the stone and cause more serious pollution.
五. General precautions: The core principle of protecting precision
Tool restrictions: It is strictly forbidden to use hard tools such as steel wool and hard plastic brushes. Microfiber cloth and natural sponge (density ≥30kg/m³) are preferred;
Frequency control: Daily cleaning is sufficient once a week. Excessive cleaning may accelerate the wear of the surface protective layer;
Maintenance combination: After cleaning, a small amount of stone curing agent (silicone-free formula) can be sprayed on the surface to enhance stain resistance and extend the service life of the precision surface.
"Prescribing the right medicine" for different stains can not only effectively remove pollution, but also protect the natural hardness and precision stability of granite measuring tools. In daily use, it is recommended to place a special cleaning kit (including neutral detergent, soft cloth, and protective agent) next to the measuring tool. Immediately deal with stains when they are found, which is more labor-saving than deep cleaning after accumulation.





