Open a coordinate measuring machine (CMM), a wafer inspection tool or a femtosecond laser system, and you will often find the same thing under the moving parts: a block of black granite.
This is not tradition. When equipment must position or measure at the micron or sub-micron level, the base becomes part of the measuring system. This article explains why granite is so widely chosen, which properties matter most, and how it is used in different types of equipment.
What a Machine Base Has to Do
In precision equipment, the base is more than a support. It must:
- Provide a flat, stable reference for guideways, air bearings and motion axes
- Keep its geometry as temperature and humidity change
- Absorb vibration from motors, moving axes and the floor
- Carry heavy loads without bending, including moving bridges, stages and workpieces
- Stay accurate for years, with minimal recalibration
Any movement in the base is added to the measurement or positioning error of the whole machine. That is why the material is chosen so carefully.
Four Properties That Make Granite the Standard
1. Thermal Stability
Temperature changes make materials expand and contract. Granite has a low coefficient of thermal expansion and low thermal conductivity compared with metals, so it responds slowly to temperature swings. Short-term changes in the room, such as a door opening or an air-conditioning cycle, have far less effect on the base. For measuring equipment, this means more stable results between calibrations.
2. Vibration Damping
Vibrations from motors, linear drives and the factory floor reduce measurement quality and positioning accuracy. Granite damps vibration much better than steel or cast iron, so the machine settles faster after a move and picks up less noise from outside. This is especially important in optical inspection, laser processing and high-speed stage systems.
3. Flatness That Can Be Lapped to Very High Accuracy
Granite has a fine, uniform structure and can be hand-lapped to extremely high flatness. Our lapping masters, most with more than 30 years of experience, can feel a difference of a few microns while working. The result is a reference surface that suits air bearings and precision linear guides.
4. Long-Term Dimensional Stability
Natural granite has very little internal stress, so it does not slowly deform over time the way some cast or welded structures can. It also does not rust, does not need oil protection and is non-magnetic. This matters for sensors, linear motors and any equipment sensitive to magnetic fields.
Where Granite Bases Are Used
Semiconductor and Wafer Equipment
Semiconductor equipment demands extreme stability, because features are measured and processed at very small scales. Granite bases and stages are used in:
- Wafer inspection and metrology systems
- Photolithography-related stages and inspection modules
- Probing and testing equipment
- Equipment assembled and calibrated in clean, temperature-controlled conditions
For these applications, granite components are often assembled in a dedicated constant-temperature, dust-controlled environment that simulates a semiconductor equipment workshop.
Coordinate Measuring Machines (CMM)
The CMM is the most familiar granite application. The base, bridge, columns and cross-rails are often made of granite, because the whole machine must hold its geometry to measure parts accurately. Granite bases for CMMs support:
- Bridge-type and gantry-type CMMs
- Video and image measuring machines
- Contour and profile measuring machines
- Guideway and lead screw measuring equipment
Laser Processing Equipment
Femtosecond and picosecond laser systems need a stable, vibration-damped platform to keep the beam focused and the motion precise. Granite bases are widely used here, often with air-bearing or linear-motor stages.
Optical and Industrial Inspection
Automated optical inspection (AOI), industrial CT and X-ray equipment use granite bases to keep sensors, sources and detectors in a fixed relationship. Dimensional stability directly improves image quality and repeatability.
Other High-Precision Equipment
- PCB drilling and routing machines
- Precision CNC machines
- XY tables and linear-motor platforms
- Perovskite coating machines
- Battery inspection equipment and tool inspection equipment
Granite Air Bearings: Taking Precision a Step Further
An air bearing floats a moving part on a thin film of compressed air, with no physical contact. This removes friction and wear, and allows very smooth, precise motion. Granite is a natural fit for air-bearing guides because:
- The lapped surface is flat and smooth enough to keep an even air film
- It does not wear, rust or contaminate
- It damps vibration, which helps motion quality
Granite air bearings are used in CMMs, CNC equipment and metrology systems where motion accuracy is critical.
Design Considerations When Specifying a Granite Base
If you are designing equipment with a granite base, these points can save time and cost:
- Define the key surfaces early (guideway faces, bearing faces, mounting faces) and the required flatness, parallelism and squareness.
- Specify the features you need, such as threaded inserts, through holes, T-slots, counterbores and precision bores with H7 tolerance.
- Think about weight and handling. Large granite parts are heavy, so lifting points and transport must be planned.
- Plan the support. The way the base is supported and leveled affects the final accuracy.
- Consider the environment. Temperature control and vibration isolation help the base perform as designed.
- Send drawings for review. An early review by the manufacturer can often reduce machining difficulty and cost.
Capability to Match Your Equipment
Precision equipment is not always small. At UNPARALLELED®, our crane and CNC equipment can process a single granite piece of up to 100 tons, with lengths up to 20 meters, widths up to 4000 mm and thicknesses up to 1000 mm.
Our production is supported by:
- Ultra-large grinding machines that can lap precision platforms up to 6000 mm long
- A temperature- and humidity-controlled workshop with a thick, hard concrete floor, isolation trenches around the room and quiet cranes to keep the measuring environment stable
- Calibrated inspection equipment, including Mahr and Mitutoyo instruments, WYLER electronic levels and Renishaw laser interferometers, traceable to national standards
- ISO 9001, ISO 14001 and ISO 45001 management systems, and CE certification
Frequently Asked Questions
Why do CMMs use granite instead of steel?
Steel expands more with temperature, conducts heat faster, damps vibration less and can rust or be magnetic. Granite offers better thermal and dimensional stability, damping and a lappable reference surface, which are all important for measurement accuracy.
Is granite used in semiconductor equipment?
Yes. Granite bases and stages are widely used in wafer inspection, metrology and other precision semiconductor equipment, where thermal stability and vibration control are essential.
What accuracy can a granite component achieve?
It depends on the size, shape and requirements. Precision granite components can be finished to micron-level accuracy, and surface plates can reach even finer flatness. Please send your drawing and tolerance requirements for a specific evaluation.
Can granite bases have holes and threaded features?
Yes. Granite can be machined with through holes, counterbores, T-slots, dovetails, vacuum grooves and threaded inserts.
How big can a granite machine base be?
At UNPARALLELED®, single pieces up to 100 tons and 20 meters in length can be processed.
Talk to Our Engineers About Your Granite Base
Whether you are developing a new CMM, a semiconductor inspection tool or a laser platform, we can support you from drawing review to finished, inspected components, including custom granite bases, granite air bearings and complete granite assemblies.






